Dodge Challenger Forum banner

Status
Not open for further replies.
1 - 15 of 15 Posts

·
Premium Member
Joined
·
1,165 Posts
Discussion Starter #1 (Edited)
2015 "Steel Curtain" Challenger
$37,500
OBO
Washington, District of Columbia


SERIOUS INQUIRIES ONLY. This listing is for my car as it is currently modified, and is for a limited time only. In the event I don’t find a buyer as modified, I plan on restoring to factory and use as a trade-in.
Feel free to share, but again, serious inquiries only. IM (Instant Message) me for further details.

2015 Challenger Scat Pack (August 2014 build date).
32,645 miles (as of date of post)

Built as ordered:
6 speed Manual
Sound Group II
Technology Group
Driver Convenience Group
VIN # 2C3CDZFJXFH704818

Modifications:
Mechanical:
* Barton Industries flat stick short throw shifter (Steelers knob
AND weighted textured racing knob included)
* Mopar Stage 1 springs
* Spohn non-adjustable rear lower control arms
* Per4mance Differential Brace (original design)
* Petty drive shaft loop
* Petty front strut brace
* NoWeeds exhaust diverters installed after cats, wired 3 way
controller; ducted to custom designed side pipes
* Side pipes: functional and designed for easy removal at track
for weight reduction
* Cracked PCM from Diablo Sport (OEM PCM also included)
* Hemifever 93 Octane tune. Married Diablo tuner included
* Skip shift eliminator and Clutch Delay Valve delete
* Ported 88mm throttle body
* 180 T-stat

Exterior:
* Custom designed "Steel Curtain" theme (fender badges, hood
stripes, hood badge)
* "Steel Curtain" themed Brembo Calipers
* Custom designed, functional George Barris inspired side pipes.
* Custom designed "Challenger" rear badge replacing "Dodge"
on trunk face
* Swirl free, meticulously maintained Pitch Black paint

Interior:
* BlackSys front and rear dash cameras with voltage regulator
* Custom designed Katzkin (sponsor) Leather seats (front and
rear) with Challenger script on seat back and "Steel Curtain"
logo on head rests. Katzkin Tuscan leather "Ink" in Barracuda
Gold (front seats ventilated)
* Custom “Steelers” head rest spacers
* Floor mats with "Steel Curtain Challenger" logo
* Amber front footwell and overhead LEDs (front only)
* Custom designed sill guards (yellow diamond plate)
* Yellow piping on doors, center console, leading edge of dash
(by windshield)

Engine Bay:
* Custom painted hood liner
* Stainless Steel mesh intake plenum cover (customized)
* Various Billet Technology bling and customized fuse box cover
* Custom ABS cover
* Painted and hydrodipped Coolant reservoir
* Hydrodipped factory CAI (top part only)
* Hellcat inspired headlight intakes

No accidents, no mechanical issues; no cosmetic issue.

This car is a show stopper! Four time Top 3 finisher in class at Carlisle Chrysler Nationals (3rd, 2 1st place and a 2nd place 2015 thru 2018), and other awards from both major and local events (Moparpalooza, Mopar Madness, etc).

The Pitch Black paint is swirl free and better looking than when delivered. Paint has been clayed, buffed, sealed and waxed to a silky smooth finish.

This car has been raced, in MSHS sponsored events (car performed flawlessly, driver less so).

Car has been meticulously maintained; all service performed by Fair Oaks Dodge in Chantilly, VA. Radiator replaced via recall.

Cold start to idle on factory, then side pipes: (headphones recommended)
 

Attachments

·
Registered
Joined
·
3,502 Posts
I'll miss that Challenger, good luck with your sale, someone will get a mean a.. Challenger !
 

·
What's Old is New Again!
Joined
·
34,557 Posts
Per Forum Rules, you must post a VIN# of the vehicle for sale. Please do this ASAP.
 

·
2012 RT Redline Tri Coat
Joined
·
3,672 Posts
Good luck with your sale.
 

·
Premium Member
Joined
·
1,165 Posts
Discussion Starter #6

·
Premium Member
Joined
·
1,165 Posts
Discussion Starter #12
I wish you luck. I tried to sell a heavily modified Challenger 3 years ago and got no offers. Traded it in, with mods on it, and took a real beating. Maybe you'll find that one individual who is looking for a car like yours!
If none of the interested parties pans out, or if the other angle I'm working doesn't pan out, I'm stripping Renny back to factory before trading in. Knew I might have to do something like this when I did the mods.
 

·
Registered
Joined
·
3,502 Posts
If none of the interested parties pans out, or if the other angle I'm working doesn't pan out, I'm stripping Renny back to factory before trading in. Knew I might have to do something like this when I did the mods.
Can't wait to see your N E W upgrade !
 

·
Registered
Joined
·
491 Posts
Wow. Shocked that you no longer like the Steelers! ;):p I really did like what you had done with it.

Good luck with the sale. Good luck on any future Challengers...if that is what you intend to do.
 

·
Premium Member
Joined
·
1,165 Posts
Discussion Starter #15
Wow. Shocked that you no longer like the Steelers! ;):p I really did like what you had done with it.

Good luck with the sale. Good luck on any future Challengers...if that is what you intend to do.
Still love the Steelers, and Challengers. Time for an upgrade, and that includes the theme!
 
1 - 15 of 15 Posts
Status
Not open for further replies.
Top