I’m going to remove mine shortly. I broke the R/T badge off my other challenger without issue, but this badge is bigger...

 

Seems to just be 4-5 push pins holding it on, but there's also a metal plate behind the grille holding it which is a pain. Let me know if you have any luck getting it off!

 

I’m working on doing the same thing.

 

Just did the same, thanks for the reply man.

 

Starts removing the R/T badge about 1 minute into the YouTube.

 

Pulled it slowly with needle nose pliers.

 

Pulled it slowly with needle nose pliers.

View attachment 173994 View attachment 173996

Did you pull it off from the front side of the grill or did you pull the retainer from the radiator side?

 

I pulled it from the front. Since the retainer was still on there in my pic, it had to force itself through the hole in the grille. I just went slow.

 

Thanks for the update.

 

I would like some opinions on removing the RT badge from the grill of a 19 scat pack and replacing it with a SRT badge. It is my pet peeve that an RT should identify the car as a 5.7l while the SRT badge should be used for any 6.4l engine, whether it is for a scat pack or 392. After all the 6.4l scat Pack and the 392 use the same engine. Added features for adaptive suspension, 6 piston vs 4 piston breaks etc. should not be used for badging. What do you think???

 

You’re right, I had the same thought... after chatting with some people in the community, seems like most still consider this upbadging.

 

I just took off both emblems. The RT badge leaves a mounting plate on grill. I used a hot exacto knife to get rid of it.

 

View attachment 183332 I just took off both emblems. The RT badge leaves a mounting plate on grill. I used a hot exacto knife to get rid of it.

Like the clean look....
How did you do it without damaging the grille?

 

I know this thread is a little old, but is there anyone who has removed theirs in one piece who wants to sell it? PM me!

 

Took mine off and ended up breaking one of the clips since the little pin was giving me a hard time lol. I also cut off the little plate with a blade and looks like nothing was there to begin with. I’m in Japan btw and car is sitting in a garage. I miss it so much.

 

Has anyone replaced it with a decent Scat Pack Grille Badge? If so, Where did you get it? I've seen several made for the charger. TIA

 

I Want to know the same. From what I’m reading and some videos I’ve watched is that
1. Buy the one that comes on the charger front grill.
2. Buy the 2019-2020 spoiler badge and use 3m tape to stick it on front grill.

 

My reasoning is, and always has been, there are people who wanted upgrades/options for their R/T's.
Hence the Scat Pack. There are those differences that go into the SRT that make it the SRT.
I consider putting the SRT badge on a Scat Pack as up badging.
Get the Bee for the grill, stay Legit.

 

I dont think putting a Charger badge on it is a good idea. Those that know the packages and have knowledge of the Challenger will know it has a 392 in it........if that is what you want people to know. But if they dont have the knowledge they wont know you have a 392 in it anyways even if it says SRT.

With knowledge though they will recognise the Charger badge....and call you on it lol. If you want people to know you have a 392, why not just get the 392 fender badge? It already has the Bee on the side that indicates that as well.

 

I found this googling Scat Pack Badges for Challengers.

 

I actually like the r/t badge in the grille! It’s quite bold

 

I actually like the r/t badge in the grille!

Same here. I think the red color “pops” nicely against the black grille.

 

I have the same car as you, I pulled mine off without breaking it just go slow, and I used needle nose pliers as well. Hopefully works for you too!